![]() Push a drill button for forward or reverse. ![]() If the light is flashing, checkįor the following: Low voltage at plug Loose motor connection Mag panel buttons are jammed or stuck If flashing light still occurs, take entire unit to an authorized serviceģ. Push the magnet button to activate the magnet. On the magnet, the drill buttons will not function. If the operator attempts to start the drill before turning 6E) The drill will not operate unless the magnet button is pushed and the red The red indicatorĭrill and Magnet Interlock (Fig. To turn the magnet off, push the Magnet button. To turn the magnet on, push the Magnet button. 6D) The magnet button must be activated before the drill will run. The tool is under load, or when the tool has stopped. NOTE: To avoid damage to the gearbox, do not shift at full speed, when To change speeds, turn the drill off and rotate the lever up or down while Speed for large diameter bits and high speed for small diameter bits (see 4292-1 operate in either high or low speed. Replace the knurled collar and tighten.Ĭat. FOR SALE The 4203 electromagnetic variable speed adjustable base. Replace the Morse Taper Socket by aligning the notches with tabsĤ. MILWAUKEE 4203 ELECTRO-MAGNETIC Adjustable Position Drill Press Base with 11in. The supplier baokang0305 carries a good stock of milwaukee 4203 adjustable position magnetic drill press base w/ 11 drill travel with the price as low as. Strike the bit tang firmly with a soft metal mallet or strike the bit tangģ. Unscrew the knurled collar and remove the entire Morse Taper Socket. To remove a bit or adapter from the socket: 1. Press the taper firmly into the socket, or use the feed handle to press Slides into the slot at the top of the socket.ģ. Line feedback speed control maintains speed and a motor/magnet lockout prevents de. Insert the taper into the socket and rotate the taper until the bit tang in direction of base length front-to-back and 20 right or left of center. Make sure the taper is clean and lightly oiled. To insert a bit or adapter into the socket: 1. Clockwise (Tighten) - Counterclockwise (Loosen) To remove the bit, insert the chuck key into one of the three holes in The 4203 electromagnetic variable speed adjustable base features solid state electronic switching and an 11-inch drill travel. ![]() Place the chuck key in each of the three holes in the chuck, turning 3 Morse Taper Amps 11. Center the bit in theĬhuck jaws and lift it about 1/32" off of the bottom. Description Milwaukee 1 Magnetic Drill, Model 4203 Serial 838B606050002 Asset 13476 Specifications: Chuck Size 1-1/4 Capacity Steel 1-1/4 Tap Size Capacity 1-14 Spindle Taper No. When using drill bits, insert the bit into the chuck. Open the chuck jaws wide enough to insert the bit. Move the housing to position the drill bit over the center of the hole.ġ. Loosen the adjusting handle located at the back of the housing base. Position the magnetic base so that the drill bit is near the desired hole Remove the chain (if drilling overhead or on a vertical surface). Drill hole (see Using Twist Drills" and "Using MILWAUKEE STEELĩ. Push the forward or reverse button as required. Check the gear speed setting and change if required. Attach the safety chain if drilling overhead or on a vertical surface. Position the unit so that the tip of the drill bit is directly over theĤ. Place the magnetic drill press on a prepared surface. Taper Socket and Using Twist Drills" and "Using MILWAUKEEĢ. Insert the bit into the chuck or socket (see Keyed Chuck" or "Morse Line Feedback speed control maintains speed and a motor/magnet lockout prevents de-mag during operation.The gear shift on the drill motor is labeled: The 4203 offers adjustability of 3/4 in direction of base length and 20 deg right or left of center. Adjustable position on this base makes lining up the bit easier and faster. ![]() The 4203 electromagnetic variable speed adjustable base features solid state electronic switching and an 11 in drill travel. Milwaukee® Drill Press Base, Adjustable Position Portable Electromagnetic, For Use With: 1/2 in and Thicker Flat Ferrous Material, 17-1/4 in Height, 4-1/4 in Width, 11 in D, 1 in Chuck, 11 in Drilling Depth, Steel ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |